“巴合曼”DH-1戶外箱標準配置
1、安裝板一塊 （鍍鋅）
2、前單開門后背板
3、門隔熱導流板一塊
4、防雨頂棚一個
5、文件袋一個
6、燈開關一套
7、安裝縱梁兩根
8、簡易包裝
1. One installation plate(galvanized)
2. One front single opening back plate
3. One door heat insulation guide
4. One rain protection tent
5. 1 Document bag
6. One set of light and switch
7. Two installation stringers
8. Simple packing
柜體顏色 RAL7032(噴塑）（戶外粉）
材料 冷軋鋼板 門2.0mm 箱體1.5mm 安裝板2.5mm 表面處理 磷化、噴塑 防護等級 IP66
Cabinet color
RAL7032 (plastic spraying)(outdoor powder)
Material
Cold rolled steel plate
Door 2.0 mm
Cabinet 1.5 mm
Installation plate 2.5 mm
Surface treatment
Phosphating, plastic spraying
Protection grade IP66
工藝特點介紹
1、柜門離地25mm
2、2.5mm厚的安裝板，兩邊有20mm寬的U形彎邊，使得安裝板強度更大，也便于搬運
3、箱體上和門上都有地線連接螺栓
4、承重鉸鏈安裝容易，換柜門也容易。柜門可開啟130°
5、安裝板利用塑料滑引器通過導軌，可柜體從正面將安裝板推入柜內
6、堅固的長方形框架不但可以加強前門的強度，還可以用來固定安裝電器元件（配合門安裝橫條使用）
7、背板能很容易地安裝，用螺絲固定；還可換裝箱門
8、防雨鎖，上、中、下三點鎖緊柜門
9、密封圈：聚氨脂發泡密封膠條，確保防護等級
10、槽型箱邊與密封圈配合防止水和灰塵落入柜內
11、左右互換開門設計，方便使用
12、標準模數化安裝孔設計，方便安裝
13、內燈，方便安裝和檢測（自選件）
14、安裝梁，不使用安裝板同樣可以進行柜內安裝
15、底座，拆卸、安裝都很方便（自選件）
16、根據需要，柜內可以加裝15-20mm厚的閉泡橡膠隔熱層（自選件）
17、防雨頂棚，防止雨水進入
18、門隔熱導流板，隔熱導流降溫
1. Cabinet door is 25mm above the ground.
2. 2.5 mm thick installation plate, both sides with U curve 20 mm width, making installation plate more strengthful, for easy transportation.
3. There are ground bolt on the cabinet and cabinet door.
4. Bearing hinge, install easily, change cabinet door also easily. Cabinet door can open 130°.
5. Installation plate makes use of plastic slip inducer over guiding rail, can push installation plate inside the cabinet from front.
6. Rigid rectangular frame can not only strengthen the strength of front door, but can also be used to fix installed electric appliance component (with horizontal door installation strip).
7. Back plate can be installed easily, fixed with screw; cabinet door can also be changed.
8. Rain protection lock can lock cabinet from top, middle and bottom three points.
9. Seal ring: polyurethane sealing strip insures protection grade.
10. Slot cabinet side and sealing rings preventing water and dust from entering cabinet.
11. Left-right interchangable opening design for ealy usage.
12. Standardarized mudular installation hole design, convenient installation.
13. Internal light, convenient installation and inspection(selective)
14. Installation beam, can also perform inside installation without installation plate
15. Base, convenient disassembly and installation (selective).
16. According to requirement, cabinet internal can be added with 15-20 mm unicellular rubber insulation layer(selective).
17. Rain protection tent, keep off rain entrance.
18. Door heat insulation guide, heat insulation guide and lower temperature.
